News:

Welcome to the new Track Trailer forum

Main Menu

Trek Tech awning bracket fitting advice

Started by Gumb, June 11, 2018, 03:43:26 PM

Previous topic - Next topic

Gumb

#15
Drill out the holes for the bolts using a 15/64th bit. I used larger washers which I already had here, than those supplied. Put silicon on the inside of the washers and push the bolts through from inside the fridge box.  Then put another set of washers on the outside (and more silicon) before placing the bracket on and bolting in to place with the spring washers under the nut.
2017 Firetail with extra fruit
2015 Pajero NX GLS

Gumb

#16
You can now assemble the bracket and lower pole. The last step is to secure the pole where it exits the box with the flat plate and rubber strip as in the picture. It should be hard up against the pole so that the pole is held firmly in place on both sides. TIP: I found it easier to get it in position by raising the awning. It was then just a matter of drilling more 15/64th holes and bolting the plate in position.

2017 Firetail with extra fruit
2015 Pajero NX GLS

Gumb

#17
In the picture above, you can see the that outer bolt of the holding plate is close to a hole where the stone guard bolt goes. With this bolt tightened, I couldn't get the stone guard back in to position because the top lip of the guard hit the nut holding the plate. Undoing that nut slightly allowed the guard to go in OK and then I tightened it up again. But it may have been a matter of taking off a corner of the top lip of the stone guard, which wouldn't be an issue anyway, since it's hidden under the shelf the bolts go through.

You will also need to adjust the middle plate further so that it slips nicely over the bracket on the side of the Tvan.   

The insulation I cut away was just secured back with a bit of silicon.



2017 Firetail with extra fruit
2015 Pajero NX GLS

Gumb

All in all, it worked well and I'm very happy with the result.

2017 Firetail with extra fruit
2015 Pajero NX GLS

JJ7488

Great write up Gumb. What size awning is that Ocam?

Gumb

#20
3m (long) and it comes out 2.5M.  Got it for $161 delivered as it was on special but $179 normal is still a good deal.

https://www.ocamindustries.com.au/3.0m-x-2.5m-car-side-awning-pullout-roof-top-tent-camper-trailer-4x4-4wd

I have a cheaper awning on the car from 4WD supacentre but it's more like a plastic than canvas. This one is light weight but appears to be a canvas type material.
2017 Firetail with extra fruit
2015 Pajero NX GLS

Topcat

Just been reading about the Trek Tech brackets - I've got height and weight restrictions. But enough about me 😄

The TVAN only just makes it down the driveway to the garage at the back of the house and I've got to lower the tyre pressure to get it in the garage.

I'm interested in a car type awning. Does anyone who has the Trek Tech brackets know how much wider the brackets are than standard and then does the awning itself extend it even further.

Appreciate any advice.
Thanks
Tony
Prado 150 GXL 6M - 2016 Mk4 TVAN Murranji

Gumb

The brackets don't increase width at all, they fit within the existing body. The actual awning is attached to the side so width increases by that amount which isn't much.

Do you mean height ?
2017 Firetail with extra fruit
2015 Pajero NX GLS

Topcat

Thanks Gumb - wasn't sure from photos.
Width is the issue - it's feeler gauge tight down the side of the house.
I'm going to get an awning for the Prado in a few weeks and will use this as a mockup.
Appreciate your advice.
Tony
Prado 150 GXL 6M - 2016 Mk4 TVAN Murranji

Gumb

#24
It's not difficult to remove the awning from the brackets so if it's too tight, just remove it when in storage. It's a quick and easy job.

One extra item you'll need is something to stop water pooling in the awning when it rains. It collects water and becomes an above ground swimming pool.  I got a tarp saver from Supapeg which just attaches to a tent pole and I put that up in the middle of the awning when it looks like rain is on the way. Works a great and can be secured to the end of the kitchen bench to stop it falling over if it's windy.
2017 Firetail with extra fruit
2015 Pajero NX GLS

Tvantim

Anybody fitted a Fiamma awning to Trek Tech brackets any thoughts or ideas, the supplied fittings design is different than a usual roll out.

Gumb

Yes, it has been done. A guy (Stuart Trevena) on the Tvan Facebook page fitted one by making an aluminium bar which attached the the Trek Tech brackets and fitted his 3m Fiamma awning to that. Made a timber bracket first out of decking board and used that as a template.

A search of the Tvan Facebook page will find his posts.
2017 Firetail with extra fruit
2015 Pajero NX GLS

tastrax

Cheers - Phil

2006 Tvan Tanami (with a few extras)
2010 Isuzu Dmax LS-U

Tvantim

Thanks for the replys on the Fiamma awning and I understand the process now.My concerns is the aluminum plank 3m long but would need a front location face of at least 100mm then how thick to keep everything rigid say 8mm. I could change the awning to 2.6m to lower the weight. My worry is the impact on the van on corrugations with this weight. Any recommendations thanks

Gumb

I'd be sticking to 3m, you need to cover as much area as possible.

To be honest, I can't see why you wouldn't just got for a normal awning which would cost a lot less and is still easy to pack up and does the job well.
2017 Firetail with extra fruit
2015 Pajero NX GLS